Stadium LED Display Products
Five product families of stadium LED display products – built for the physical reality of sports venues — from pitch-side perimeter boards to center-hung scoreboards, court-side rings, LED posters, and custom stadium systems. Each designed, tested, and supported as part of one turnkey platform.
- 01 Perimeter LED Displays P6–P10 · Outdoor · Sponsor rotation
- 02 Center-Hung Scoreboards 360° cubes · Replay · Stats
- 03 Court-Side LED Rings P4–P6 · Indoor · Low-glare
- 04 LED Poster Displays Floor · Wall · Ceiling mount
- 05 Custom Stadium Systems Bespoke geometry · Full engineering
Every Product Built on the Same Stadium-Grade Engineering
Whether it’s a perimeter board, a center-hung cube, or a custom system, every product we ship is built to the same engineering standards — designed for sunlight, rain, stadium rigging, and live broadcast timing.
GOB Package
COB/GOB/SMD Encapsulation
Each LED module is sealed with a layer of optical glue, protecting the pixel from moisture, dust, and impact — extending module lifespan by up to 40% versus conventional SMD.
6,500 Nits
High-Brightness Outdoor
Up to 6,500 nits brightness with automatic dimming sensors — readable in direct sunlight during a day match, and dimmable at night without losing contrast.
IP65 / IP66
Weatherproof Enclosure
Front and rear sealed LED panels rated IP65 (or IP66 on request) — engineered for rain, dust, UV, and long-term outdoor installation without corrosion.
3840 / 7680 Hz
Broadcast-Grade Refresh
3840Hz standard LED display for smooth sports live broadcating; up to 7680Hz on studio-grade models — eliminating flicker on TV cameras and slow-motion replays.
Front / Rear
Dual Service Access
Front-service for tight installations (no rear access required), rear-service for open-access rigs — one cabinet platform supports both service modes.
< 10 ms
Low-Latency Sync
Sub-10ms signal latency across perimeter rings, center-hung cubes, and entry displays — one unified visual frame, regardless of screen count.
Every Product Available as Indoor or Outdoor Series
All five stadium LED display product families are available in two platform variants — Indoor Series LED display for arenas and court-side installations, Outdoor Stadium Series LED display for perimeters and scoreboards. Below are the standard specifications; custom configurations are available for specific projects.
| Parameter | Indoor Series | Outdoor Stadium Series |
|---|---|---|
| Pixel Pitch | P0.9 – P4.81 Arena, court-side, center-hung | P4.0 – P10.4 Perimeter, scoreboard, billboard |
| Brightness | 800 – 1,500 nits Auto-dimming for indoor glare control | Up to 10,000 nits Readable under direct sunlight |
| Refresh Rate | 3,840 Hz standard 7,680 Hz available on studio models | 3,840 Hz – 7,680 Hz Broadcast & slow-motion replay safe |
| Protection Rating | IP30 – IP54 Dust and moisture protected | IP65 / IP66 Rain, dust, UV, anti-corrosion |
| Viewing Angle | H 160° / V 160° Uniform color at all seat positions | H 160° / V 160° Wide enough for pitch-side viewing |
| Service Mode | Front & rear serviceable Magnetic module removal | Front & rear serviceable Rear access for elevated installs |
| Operating Temperature | -10°C to +50°C Standard indoor range | -30°C to +60°C Extended outdoor range |
| Encapsulation | COB / GOB GOB recommended for heavy-traffic venues | SMD standard Moisture + impact protection |
Specifications of GobLED stadium LED display products above are standard configurations. Custom pixel pitch, brightness, cabinet geometry, and IP ratings are available for specific projects.
Request Full Spec SheetEvery Cabinet Goes Through Five Test Gates
Before any stadium LED display product leaves our factory, it has already survived the conditions it will face in the field — heat, water, voltage stress, and 72 hours of continuous operation. These five test gates apply to every product family we ship.
Incoming Material Inspection
LED lamps, IC drivers, PCB boards, and power supplies are batch-tested on arrival — bin sorting, brightness consistency, and electrical parameters verified.
Module Aging Test (72h)
Every module runs continuously for 72 hours at 100% white full-brightness — screening out early-life failures before assembly.
COB/GOB/SMD Encapsulation Check
Optical glue thickness, bubble inspection, and adhesion test on every module — ensuring the GOB layer performs as designed, not just looks it.
Cabinet Waterproof & IP Test
Random-sampled cabinets undergo IP65/IP66 spray testing — sealing, connectors, and cable glands checked under real water pressure.
Final Calibration & Factory Burn-In
Full-screen color calibration at 6500K, brightness uniformity scan, and a final 24-hour burn-in — then sealed, packaged, and shipped with a test report.
AGING · 72H
IP65 · TEST
CALIBRATIONRequest the Full Product Catalog
Tell us which product family you’re interested in, and we’ll send the full catalog — specifications, dimensions, pixel pitch options, and installation requirements.
Request Product Catalog
Fill in the form and our team will respond within 24 hours.